Panasonic tx-32c20e.
Proizvodac.Czech Republik.
Maticna ploca.TNP OEAO17
Model sasije.Mdk332-o w
T-con na maticnoj
Tjuner -ENG 37F03KF .Analog-Digital
Napajanje -PSC10319D M
Inverter na napajackom modulu.
Kvar,tv nakon nekoliko pokusaja upali i nakon 15 min se cije rele da iskljuci
Poslije toga led blinka 12 puta,
kad led blinka nema napona
Kad ugasim prekidac na tv i ponovo 2-3 puta pokusam upali ,radi 10-15 min cuje se rele da otpusti i pocne crvena lem 12 puta blinkati.
[ODUSTAO vlasnik] PANASONIC TX-L32C20E PROBLEM,
-
nele2222
- Expert
- Postovi: 624
- Pridružen/a: 24 lip 2014 22:33
Po blinkanju bih rekao da je Audio u pitanju , mada ne mora da znaci.
Pozdrav svim ucesnicima
-
Radovan74
- Expert
- Postovi: 359
- Pridružen/a: 31 sij 2012 23:40
- Lokacija: Backa Palanka
Trebalo bi da je audio kao sto kaze nele.
Neki dan sam radio panasonic sa 12 blinkanja. Kvar je bio na audio ploci.
Ovo je za Panasonic 52"..
12 Blinks SOS: On the A board, transistor Q2301 monitors the Sound 15V line and the operation ofthe audio power amplifier IC2301. If the audio output circuit, IC2301, or the 15V lines develops ashort to ground, transistor Q2301 goes into conduction and applies a high to pin 118 of the MPU,IC1100, triggering a SOS condition. The power LED blinks 12 times.
12 Blinks SOS: We have also discovered that 12 blinks of the power LED may also be caused by adefective SS board. To determine the source of the shutdown, disconnect the connector D5 andconnect the unit to the AC source. If the panel turns on and the LEDs of the SS and SC boards stayon, the problem is on the A board. If the panel does not stay on, the problem is likely to be the SSboard."
Neki dan sam radio panasonic sa 12 blinkanja. Kvar je bio na audio ploci.
Ovo je za Panasonic 52"..
12 Blinks SOS: On the A board, transistor Q2301 monitors the Sound 15V line and the operation ofthe audio power amplifier IC2301. If the audio output circuit, IC2301, or the 15V lines develops ashort to ground, transistor Q2301 goes into conduction and applies a high to pin 118 of the MPU,IC1100, triggering a SOS condition. The power LED blinks 12 times.
12 Blinks SOS: We have also discovered that 12 blinks of the power LED may also be caused by adefective SS board. To determine the source of the shutdown, disconnect the connector D5 andconnect the unit to the AC source. If the panel turns on and the LEDs of the SS and SC boards stayon, the problem is on the A board. If the panel does not stay on, the problem is likely to be the SSboard."
-
kokan
- Expert
- Postovi: 334
- Pridružen/a: 05 lip 2012 06:23
U pitanju je šasija GLP25, a za 12 ''power LED'' blinking piše: ''BE(sLD)SOS A BOARD''. Šta god da to znači....
-
Jordan Čebron
- Expert
- Postovi: 504
- Pridružen/a: 25 ožu 2014 16:30
- Lokacija: Nova Gorica SLO
Greška na matični ploči (SSB boaed)
-
e70xk
- Mlađi član
- Postovi: 26
- Pridružen/a: 07 kol 2013 16:55
Zahvaljujem na pomoci,maticna ploca je problem ,stranka odustala od popravka,