Producer/Proizvođač - Sony LCD
Model No/Oznake modela - KDL-26S5500
Chassis/Model šasije -
Main board/Matična ploča - FLX00018746-110
LVDS/TCON -
MCU/Procesor - PNX8541E/2009
Scaler/Scaler -
Eeprom -
Flash -
Audio/Ton -
Tuner analog/digital -
Inverter/Backlight -
Lcd display/Panel - V260B1-L11
Power supply(SMPS)- APS-243
Tuner -
Opis kvara i opis poduzetih radnji i merenja na aparatu:
TV je dosao sa siptomom kad se prikljuci na napon zasvetli zelena led skljocne relej pa ga vrati nazad i tako pokusa tri puta posle toga krece da blinka crvena led 5 puta sa pauzom od 3sek, nema ni slika ni ton kad skljocne relej. Naponi iz mreze su ok, molim za pomoc-savet?
LCD Sony Bavaria 5 puta blinka
Ako ti može pomoći.
Sony Bravia KDL LCD TV error codes for red led blinking flashing light
Red led light blinks flashes, red light error code troubleshooting Chart, TV shutsdown
Always try power reset, unplug powercord for 5 mins then factory reset tv & update with usb drive from sony site- http://esupport.sony.com/US/perl/swu-do ... pd_id=7151
0 no red standby light-check powercord or bad main logic board or power board, check standby volts
1 red blink not used
2 red flashes is bad power board, solution replace power board
3 red flashes is bad main logic or power board, check for standby volts if ok replace main logic board
4 red blinks- can be LD board or main logic board, check inverter board wires for arcing to ground
5 red flashes- bad lcd panel connection or internal lcd short- squeeze bezel to locate bad connection
6 red flashes- backlight issue, bad main board, or power board or inverter boards- check standby volts on power board. "backlight on" volts should be 3-5v from main logic board then 24v to inverter
7 red flashes- main board over heating, can be short on power board or main logic board
8 red flashes- main board sp prot, try power reset, update with usb, or replace main logic board
9 blinks- check fan error, * if TV has fans
10 blinks- digital board or tuner board * some Sony TVs may not have this board
11 red flashes- bad main board, bad IC, replace main logic board
12 red light flashes is tcon error bad T-con board or bad LCD panel, replace tcon board usually
13 red flashing is backlight balance error bad lcd panel or inverter boards (common) or bal board on kdl-52v4100 only, replace inverter board usually then main logic board
14 red flashes HFR- bad TCON or Bad LCD panel, replace tcon board. unplug tcon board if tv stays on without tcon board replace tcon board.
Sony Bravia KDL LCD TV error codes for red led blinking flashing light
Red led light blinks flashes, red light error code troubleshooting Chart, TV shutsdown
Always try power reset, unplug powercord for 5 mins then factory reset tv & update with usb drive from sony site- http://esupport.sony.com/US/perl/swu-do ... pd_id=7151
0 no red standby light-check powercord or bad main logic board or power board, check standby volts
1 red blink not used
2 red flashes is bad power board, solution replace power board
3 red flashes is bad main logic or power board, check for standby volts if ok replace main logic board
4 red blinks- can be LD board or main logic board, check inverter board wires for arcing to ground
5 red flashes- bad lcd panel connection or internal lcd short- squeeze bezel to locate bad connection
6 red flashes- backlight issue, bad main board, or power board or inverter boards- check standby volts on power board. "backlight on" volts should be 3-5v from main logic board then 24v to inverter
7 red flashes- main board over heating, can be short on power board or main logic board
8 red flashes- main board sp prot, try power reset, update with usb, or replace main logic board
9 blinks- check fan error, * if TV has fans
10 blinks- digital board or tuner board * some Sony TVs may not have this board
11 red flashes- bad main board, bad IC, replace main logic board
12 red light flashes is tcon error bad T-con board or bad LCD panel, replace tcon board usually
13 red flashing is backlight balance error bad lcd panel or inverter boards (common) or bal board on kdl-52v4100 only, replace inverter board usually then main logic board
14 red flashes HFR- bad TCON or Bad LCD panel, replace tcon board. unplug tcon board if tv stays on without tcon board replace tcon board.
Online
Trenutno korisnika/ca: Claude [Bot] i 0 gostiju.